410 test

Talk about 20, 16, & 28 gauge and .410 bore shotguns here.
Post Reply
SumToy
Posts: 280
Joined: July 2nd, 2012, 7:39 am

410 test

Post by SumToy » December 1st, 2017, 10:59 am

Ok I was playing around some. Threaded a 28 inch and shot it. Then cut it to 24 inch and threaded it. The 24 inch picked up 21 shot with 2 loads and 30 shot with one load. Just trying to get some feed back on the little devils. Is the powder yall run fast or slow burn.

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 4292
Joined: August 15th, 2011, 9:15 pm
Location: Argos Indiana

Re: 410 test

Post by hoobilly » December 1st, 2017, 11:08 pm

cut that sucker to 21" and see if it does better or worse lol

cant believe no one with a 410 on here reloads and knows how fast or slow their powder is..

User avatar
GLS
Gobbler Nation
Gobbler Nation
Posts: 2360
Joined: May 16th, 2012, 10:29 am
Location: Lowcountry, GA

Re: 410 test

Post by GLS » December 2nd, 2017, 6:36 am

I took possession of that gun (Yildiz single-shot) yesterday and no one is going to cut that barrel. ;) I didn't load the shells he used, but I assume it's the same powder I use. In looking at a shotgun powder burn rate chart of about 150 powders, the powder is somewhere in the middle. I don't recognize any use of the powders slower than what I use in load, so for purposes of answering William, this is a slow burning powder. If this sounds vague, it is deliberately so. :) I'll get photos of the gun up after it's rigged. 144 in the 10 ring at 40 measured yards using #9 is pretty damn good from where I sit and hopefully brass hulls will up the count. Gil

SumToy
Posts: 280
Joined: July 2nd, 2012, 7:39 am

Re: 410 test

Post by SumToy » December 2nd, 2017, 7:20 am

Hoobilly I understand to a point why. I don't care who load or what load someone shoots. I may or may not care for the person/company but if load is good and safe so be it. That is why I never post much about load I have tested. I try to figure out what works best in set up. I have idea what it is. That is why I ask.

User avatar
GLS
Gobbler Nation
Gobbler Nation
Posts: 2360
Joined: May 16th, 2012, 10:29 am
Location: Lowcountry, GA

Re: 410 test

Post by GLS » December 2nd, 2017, 7:24 am

And William did a great job on this gun. It's a beaut. Gil

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 4292
Joined: August 15th, 2011, 9:15 pm
Location: Argos Indiana

Re: 410 test

Post by hoobilly » December 2nd, 2017, 9:03 am

GLS wrote:And William did a great job on this gun. It's a beaut. Gil
I thought it was a test gun lol

He does good work.


Sent from my iPhone using Tapatalk

SumToy
Posts: 280
Joined: July 2nd, 2012, 7:39 am

Re: 410 test

Post by SumToy » December 2nd, 2017, 9:09 am

hoobilly wrote:
December 2nd, 2017, 9:03 am
GLS wrote:And William did a great job on this gun. It's a beaut. Gil
I thought it was a test gun lol

He does good work.


Sent from my iPhone using Tapatalk
You should have been on phone with him when I said lets cut it. It was almost like I was talking to Mel Tillis :D No way I was going to say anything about 20 inches. :LMAO:
Last edited by SumToy on December 2nd, 2017, 3:22 pm, edited 1 time in total.

User avatar
howl
Posts: 759
Joined: April 25th, 2013, 9:26 am
Location: Middle GA

Re: 410 test

Post by howl » December 2nd, 2017, 12:37 pm

I ain't sayin' nothin', because I don't know nothin'.

I think what we need is a shortened 28 gauge shell, in a short 28 gauge gun, using .410 strength loads, going out a suppressor with a built in turkey choke. Make that suppressor titanium.

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 4292
Joined: August 15th, 2011, 9:15 pm
Location: Argos Indiana

Re: 410 test

Post by hoobilly » December 2nd, 2017, 2:37 pm

SumToy wrote:
hoobilly wrote:
December 2nd, 2017, 9:03 am
GLS wrote:And William did a great job on this gun. It's a beaut. Gil
I thought it was a test gun lol

He does good work.


Sent from my iPhone using Tapatalk
You should have been on phone with him when I said lets cut it. It was almost like I was talking to Mel Tillis :D Now way I was going to say anything about 20 inches. :LMAO:
LOL


Sent from my iPhone using Tapatalk

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 4292
Joined: August 15th, 2011, 9:15 pm
Location: Argos Indiana

Re: 410 test

Post by hoobilly » December 2nd, 2017, 2:37 pm

howl wrote:I ain't sayin' nothin', because I don't know nothin'.

I think what we need is a shortened 28 gauge shell, in a short 28 gauge gun, using .410 strength loads, going out a suppressor with a built in turkey choke. Make that suppressor titanium.
I like how you think. Surrounding gobblers would never hear the shot


Sent from my iPhone using Tapatalk

User avatar
GLS
Gobbler Nation
Gobbler Nation
Posts: 2360
Joined: May 16th, 2012, 10:29 am
Location: Lowcountry, GA

Re: 410 test

Post by GLS » December 2nd, 2017, 3:05 pm

Other than 2shooters two Yildie .410 single-shots, you won't see prettier wood on a NIB gun costing under $130.

Image

User avatar
howl
Posts: 759
Joined: April 25th, 2013, 9:26 am
Location: Middle GA

Re: 410 test

Post by howl » December 2nd, 2017, 6:28 pm

I like that curl. Pretty wood doesn't make them shoot any better, but it does add intangible value.

2Shooter
Posts: 620
Joined: January 6th, 2016, 9:18 pm
Location: North Georgia

Re: 410 test

Post by 2Shooter » December 2nd, 2017, 8:39 pm

GLS wrote:
December 2nd, 2017, 3:05 pm
Other than 2shooters two Yildie .410 single-shots, you won't see prettier wood on a NIB gun costing under $130.

Image
Dang Gil, that is some beautiful wood on that Yildiz popgun!!! ;) :thumbup: Got to get mine to William, and get him to cut the barrel down to 24", and add a choke.

Post Reply

Return to “Small Bore”

Who is online

Users browsing this forum: No registered users and 4 guests